Fitting the 1911 Barrel, Part 4: Headspace

Fitting the 1911 Barrel, Part 4: Headspace

When factory 1911 barrels are produced, the chamber is cut measuring from the rear edge of the hood forward. As you remove material from the hood to fit the barrel to your slide, you are shortening headspace. If you drop a round into a barrel with short headspace, the rim will be above flush with the rear surface of the hood. This condition may prevent the barrel from locking. I have seen "drop in" barrels from major manufacturers with short headspace.

When the barrel is locked in firing position, the chamber end is higher than the muzzle and the cartridge base is actually making contact with the breech face at a slight angle.

My Clymer .45 ACP Go gauge measures .900 inches but we will need a bit more headspace for reliability so the round will not bind during chambering and also to allow a little room for crud.

Years ago I made my own Go and No/Go gauges for barrel fitting measuring .903 inches and .906 inches, respectively. The SAAMI No/Go spec is .920 inches, and I have only seen one pistol that would chamber a .920-inch gauge in decades of working on 1911s. The .45 ACP is a low pressure cartridge with generous allowable headspace dimensions, but if you are chambering a more intense round like .38 Super, the specs will be tighter.


Install the barrel in the slide with the Kart bench bushing, drop your Go gauge in the chamber and attempt to push the barrel up into locked position. The likelihood is the barrel will not fully lock. Remove the barrel and clamp it vertically in a vise.


The chamber will have to be reamed with a headspace reamer a little bit at a time until the barrel locks. Use cutting oil and go slow. You will note from the pictures I have installed a sleeve on my chambering reamer to control the depth of cut.


The depth of cut is controlled with feeler gauges between the sleeve and the barrel hood. Start with a .020î gauge, take a cut, check headspace.

If the chamber needs to be cut deeper, I go to the next smaller feeler gauge and take another cut. In this way, I closely control cutting depth. No mistakes, no overcut chambers.

Once your "Go" gauge will chamber normally, add a .003-inch feeler behind it. When the barrel will fully lock up with the "Go" gauge in place and a .003-inch feeler gauge, you're done. Try a .006-inch feeler as a No/Go check, but don't use the actual No/Go gauge. In fact, there really isn't any reason to buy a No/Go .45 ACP gauge.


At this point, we have fitted the hood, bottom lugs, link and cut the chamber. The last fitting step is the bushing. Stay tuned.

The Tools

Here are the tools needed for headspacing a .45 automatic: chambering reamer with sleeve, feeler gauges, Kart bench bushing and headspace gauge(s).

Short Headspace

Short headspace may cause the rim of the cartridge to protrude above the barrel hood, preventing the barrel from fully locking into the slide.

Go Gauge

Check headspace by attempting to press the barrel into full lockup with the Go gauge chambered. Most of the time, it won\'t quite go into position.

Lengthening the Chamber

Adjust headspace by carefully lengthening the chamber with a chambering reamer. This sleeved reamer uses feeler gauges to control depth of cut.

Recommended for You

Ontario Chief Firearms Officer, Dwight Peer, spoke with TheGunBlog.ca about the Canada-wide surge in buying AR-15 target rifles. 2nd Amendment

Ontario, Canada Chief Firearms Officer Comments on AR-15 Buying Surge and Gun Licensing

TheGunBlog.ca - July 16, 2019

Ontario Chief Firearms Officer, Dwight Peer, spoke with TheGunBlog.ca about the Canada-wide...

The last of Germany's infamous Elefant tank destroyers. Historical

World War II German Elefant Tank Destroyers

Neal S Shera - July 12, 2019

The last of Germany's infamous Elefant tank destroyers.

Berger Bullets is now shipping the new 6.5mm 156gr EOL Elite Hunter projectiles to exclusive retailers. Ammo

Berger 6.5mm 156gr EOL Elite Hunter Bullets Available Now

Berger Bullets - July 10, 2019

Berger Bullets is now shipping the new 6.5mm 156gr EOL Elite Hunter projectiles to exclusive...

See More Recommendations

Popular Videos

New Bushnell Prime 1700 and Nitro 1800 Rangefinders

New Bushnell Prime 1700 and Nitro 1800 Rangefinders

Jake Edson of Bushnell Optics tells OSG's Lynn Burkhead about the brand new Prime 1700 and Nitro 1800 rangefinders.

Springfield Armory Saint Victor in .308

Springfield Armory Saint Victor in .308

The Saint Victor in .308 features a 16" light weight barrel, M-LokĀ® free float hand guard and included flip-up sights.

New addition to the Browning X-Bolt rifle series

New addition to the Browning X-Bolt rifle series

New for 2019 is the Max Long Range model featuring a composite Max stock with fully adjustable comb, spacers for adjusting length of pull, stainless fluted heavy sporter barrel, threaded muzzle brake and extended bolt handle.

See more Popular Videos

Trending Stories

Please sign and share the petition to get the required 100,000 signatures by July 27. 2nd Amendment

Tell the White House that the 2nd Amendment Was Not Given to the People by Government

Firearms News - July 02, 2019

Please sign and share the petition to get the required 100,000 signatures by July 27.

A $50 Ring Loc-Kit gives AirForce Condor airgunners unparalleled power and accuracy. Air Guns

AirForce Airguns Condor Ring-Loc Kit Review

Tom Gaylord - May 29, 2019

A $50 Ring Loc-Kit gives AirForce Condor airgunners unparalleled power and accuracy.

The last of Germany's infamous Elefant tank destroyers. Historical

World War II German Elefant Tank Destroyers

Neal S Shera - July 12, 2019

The last of Germany's infamous Elefant tank destroyers.

See More Stories

More Gunsmithing

On the bench in front of me was a customer's M&P Shield he'd dropped off complaining about the Gunsmithing

Apex M&P Trigger Kits

Gus Norcross - July 11, 2014

On the bench in front of me was a customer's M&P Shield he'd dropped off complaining about...

YouTuber, GunCraft101, builds an AR-10 from used brass casings. Gunsmithing

YouTuber Builds AR-10 Receiver from Used Brass Cartridge Cases

Jim Grant - July 06, 2018

YouTuber, GunCraft101, builds an AR-10 from used brass casings.

I rolled onto the range late in the afternoon with a couple rifles to test-fire. I had it all to Gunsmithing

Savage Trigger Upgrade From Sharpshooter Supply

Gus Norcross - April 02, 2014

I rolled onto the range late in the afternoon with a couple rifles to test-fire. I had it all...

See More Gunsmithing

GET THE MAGAZINE Subscribe & Save

Temporary Price Reduction.

SUBSCRIBE NOW

Give a Gift   |   Subscriber Services

PREVIEW OUR CURRENT ISSUE

GET THE NEWSLETTER Join the List and Never Miss a Thing.